How to Reset a Vokera Boiler? Step-By-Step Guide
To reset a Vokera boiler, press and hold the reset button on the control panel for a few seconds until it switches off and starts again. You can also reset it by turning the mode selector dial to the ‘Off/Reset’ setting, then back to your chosen heating mode.
If the green light keeps flashing or you see error codes such as AL40 or AL41 after resetting, or if the boiler still won’t work, this usually points to a bigger problem.
In that case, you’ll need to contact a Gas Safe registered engineer.
In this brief guide, we’ll walk you through the process of resetting your Vokera boiler, allowing you to solve typical boiler difficulties with confidence and ease.
Here is the step-by-step guide on how to reset a vokera boiler
- Before attempting to reset your boiler, cut off the electricity supply to the boiler. To turn off the power, find the electrical switch or circuit breaker that is attached to the boiler and flip it off.
- Give the boiler time to cool down.Wait at least 10 to 15 minutes before attempting the reset.
- Locate your Vokera boiler’s reset button. It’s normally located on the front panel and may be labeled “Reset” or indicated by a symbol.
- Once the boiler has cooled, press and hold the reset button for around five seconds. If the button is recessed, you might need to reach it with a pen or small tool.
- After holding the reset button for the specified time, release it. You should hear a clicking sound, indicating that the reset process has been initiated.
- Allow the boiler a few minutes to reset and restart. During this time, you may hear noises as the boiler’s components interact.
- After the restart, keep an eye on the boiler to check that it is functioning properly. Look for issue codes or warning lights on the display panel.
- Turn on the thermostat and test the heating system to ensure it works properly. Check that the boiler provides hot water and that the radiators heat properly.
- While a reset might solve minor difficulties, it is essential to deal with any underlying issues that may have contributed to the initial problem. If the problem persists after resetting the boiler, consult with a trained heating professional for further diagnosis and repair.
- After you’ve established that the boiler is working properly, turn on the electrical switch or circuit breaker.
Vokera boiler reset button location
The Vokèra boiler reset button is usually located on the front panel and may be marked “Reset” or shown with a flame symbol. On some models, there isn’t a separate button.
Instead, you reset the boiler by turning the mode selector dial to the ‘Off/Reset’ position, then back to ‘Heating & Hot Water’ or ‘Hot Water Only’.
If you can’t see a reset button, check under the front flap or refer to your user manual for exact instructions.
vokera boiler troubleshooting
Why do you need to reset a vokera boiler?
Before diving into the reset process, it’s essential to understand why your Vokera boiler might require a reset. Common reasons include:
-
- When there is a power outage, the boiler may shut down or enter a safety lockout mode.
- Vokera boiler not firing up
- If the boiler detects that it’s overheating.
- Insufficient water pressure can cause the boiler to malfunction and require a reset.
- Sensors, valves, and other components may require a reset.
- Problems with the gas supply, such as a faulty gas valve, may demand a reset.
PlusHeat Expert Guide
Knowing how to reset your Vokera boiler can be crucial for addressing common issues like power outages, overheating, low water pressure, faulty components, or gas supply problems.
By following our guide, you can safely and effectively reset your boiler, restoring warmth and comfort to your home.
Remember to
- Prioritize safety,
- Monitor the system after resetting, and
- Address any underlying issues to ensure optimal performance.
With these steps, you can confidently troubleshoot and resolve boiler difficulties with ease.
Also Read –
- How to reset Baxi Boiler?
- How to reset a Worcester boiler?
- Vokera Boiler Not Working? Common Issues and How to Fix